URBAN EM110 with conveyor 2,6 m

The branch logger URBAN EM110 is driven by a three phase 18,5 kW electric motor SIEMENS (connects to a 63 A socket). Also available with a 15 kW electric motor at customers request (32 A socket). The motors output is transferred via V-belts to the oil filled gearbox which drives the blade rotors. The EM110 can handle a larger branch diameter than EM70. This model is very ideal for processing waste material (boards up to width 280 mm, cut-offs) and also smaller stems up to 12 cm diameter. The final lenght of chips is 7 -22 cm.

UP TO DIAMETER 120 MM

Part of the machine is:  operators manual including declaration of conformity.

  • Category: URBAN EM110
  • Model series:110
  • Catalogues code:EM110 D2,6
  • Offered from:24.02.2017
  • Availability :within 2 weeks
Weight: 1048 kg
Max. diameter of soft freshwood (pine): 120 mm
Max. diameter of fresh hardwood (oak, hornbeam): 100 mm
Max. diameter of dry hardwood (oak, hornbeam): 80 mm
Max. diamensions of block of wood (spruce): 100 x 100 mm
Max. diameter of wooden board (spruce): 280 x 40 mm
Log length (not adjustable): 7 - 22 cm
Logging device inlet dimensions: 290 x 290 mm
Inlet hopper dimensions: 800 x 600 mm
Blade rotation speed (rpm): 160 / min.
Top performance: 10 m3/h
Engine power: 18,5 kW (socket 63 A)
Number of logging blades: 6
The gap between the blade of the cutting blades: approx. 0,1 mm
Lifetime of blades per one grinding: 150 - 800 m3 of of small logs
Overload protection: Slip + thermal protection
Dimensions in transport position (length x width x height): 248x126x338 cm
Dimensions in working position (length x width x height): Závisí na poloze dopravníku
Packaging dimensions (length x width x height): 446x126x235 cm
Logs output: Conveyor 2,6 m
Conveyor drive: V-belt drive
Height of the end of conveyor at angle of 30°: 185 cm
Height of the end of conveyor at angle of 40°: 222 cm
Videos from Youtube:

The electric motor

The branch logger URBAN EM110 is driven by a three phase 18,5 kW electric motor SIEMENS (connects to a 63 A socket). Also available with a 15 kW electric motor at customer´s request (32 A socket). The motor´s output is transferred via V-belts to the oil filled gearbox which drives the blade rotors.

 

The frame

The EM110 is designed for stationary using. The machine frame has 4 rigid legs and its lower part is adapted for forklift trucks. Two suspension lugs at the top of the machine can also be used for handling.

 

The belt conveyor

It is used a 2.6 m long belt conveyor driven by V-belt. The conveyor slope is adjustable by a winch. The conveyor is lifted to the vertical position during transport. It is possible to install on the end of conveyor following accessories: the 0,8 m slide or a double bagging device with a support leg. The bagger is attached by four screws and assembly takes only a few minutes.

 

The inlet hopper

The hopper is long enough to provide safety and is equipped with a safety shut-off frame, which by pressing down stops the engine. The inlet hopper is oriented horizontally, which greatly facilitates insertion of long branches compared to the vertical or sloping hopper. Surface treatment of the whole machine is made with powder paint.

 

The Overload protection

The logger is protected against overloading by the thermal protection of motor and by V-belt drive. When a too strong branch is inserted, the belt will slip and the motor will be stopped. If they do, the knife blades will usually be bite in the branch and can not be freely removed from the hopper. The supplied lever is used to release it. Release the branch by clockwise lever rotating. 

 

The chipping device

The working principle of branch loggers URBAN lies in two counter rotating shafts with knives. The rotating knives draw in the wood material into the feed hopper unassisted. The passage gap between the shafts is 110 mm. Each shaft has 3 fixed knives, made from high quality tool steel. It is possible to resharpen the knives repeatedly. After sharpening there is a pad to be put under the knives in order to keep the same gap between the knives (c. 0,1 mm). One single sharpening of knives is capable of producing from 150 to 800 solid meters of small logs, depending the level of contaminants (mud, nails, stones etc.). Each blade can be sharpened up about 4 mm, then it must be replaced with a new one.

If you have a question about this product, do not hesitate to ask.

Items marked * are required.

Product variants

URBAN EM110 with Big-bag bagging within 2 weeks
URBAN EM110 with folding conveyor 4,1 m within 3 weeks
URBAN EM110 with double bagging within 2 weeks

Optional accessories

Bags for logs