URBAN SMH70 with belt conveyor 2,1 m

The Branch Logger URBAN SMH70  is powered by a 10 hp (optionally 14 hp) Briggs & Stratton VANGUARD engine. The power is transmitted from the engine by the V-belts on an oil-filled gearbox which drives the logger. The logger has road trailer with number plate bracket for easy transport to any place. 

UP TO DIAMETER 80 MM

Part of the machine is: operators  manual including declaration of conformity and  technical license for trailer.

 

  • Category: URBAN SMH70
  • Model series:70
  • Catalogues code:SMH70 D2,1
  • Offered from:02.03.2017
  • Availability :within 4 weeks

Product variants

Photo Variant
URBAN SMH70 with belt conveyor 2,6 m within 4 weeks
URBAN SMH70 with turntable and belt conveyor 2,1 m within 4 weeks
URBAN SMH70 with turntable and belt conveyor 2,6 m within 4 weeks
URBAN SMH70 with folding conveyor 3,4 m within 4 weeks
URBAN SMH70 with turntable and folding belt conveyor 3,4 m within 4 weeks
URBAN SMH70 with double bagging within 4 weeks
Weight (kg): 514
Max. diameter of soft freshwood (pine): 80 mm
Max. diameter of fresh hardwood (oak, hornbeam): 65 mm
Max. diameter of dry hardwood (oak, hornbeam): 50 mm
Max. diamensions of block of wood (spruce): 60 x 60 mm
Max. diameter of wooden board (spruce): 190 x 20 mm
Log length (not adjustable): 6 - 13 cm
Logging device inlet dimensions: 200 x 200 mm
Inlet hopper dimensions: 700 x 400 mm
Blade rotation speed (rpm): 200 / min.
Top performance: 4 m3/h
Engine power: 7,5 kW (10 hp)
Fuel: Unleaded fuel (95)
Fuel tank volume: 4 l
Average gas consumption: 1 - 1,5 l/h
Number of logging blades: 6
The gap between the blade of the cutting blades: approx. 0,1 mm
Lifetime of blades per one grinding: 100 - 500 m3 of small logs
Chassis: Road with license plate
Overrun brake: No
Overload protection: Belt slip
Dimensions (length x width x height): 311x153x290 cm
Dimensions in working position (length x width x height): Depends on conveyor position
Packaging dimensions (length x width x height): 311x153x250 cm
Length without towing bar: 205 cm
Logs output: Conveyor 2,1 m
Conveyor drive: V-belt drive
Height of the end of conveyor at angle of 30°: 181 cm
Height of the end of conveyor at angle of 40°: 211 cm
Videos from Youtube:

The engine

The SM70 is driven by a four stroke 10 hp Briggs & Straton VANGUARD engine, with pull cord or optional electric starter. The engine´s output is transferred via V-belts to the oil filled gearbox which drives the blade rotors. The fuel tank capacity is 4 litres. Upon request, a logger can be equipped by hour meter.

 

The road trailer

The logger has unbraked road trailer with number plate bracket. There is a one pull-out wheel in the front of trailer and two adjustable legs on the back side of trailer. The machine is connected to a vehicle with a 50 mm diameter tow ball. The total weight of the trailer with logger is 440 kg. The maximum written weight in the registration certificate is 600 kg. The centre of gravity of the machine is slightly before the axle.

 

The belt conveyor

It is used a 2,1 m long belt conveyor driven by V-belt. The conveyor slope is adjustable by a winch. The conveyor is lifted to the vertical position during transport. It is possible to install on the end of conveyor following accessories: the 0,8 m slide or a double bagging device with a support leg. The bagger is attached by four screws and assembly takes only a few minutes.

 

The inlet hopper

The hopper is long enough to provide safety and is equipped with a safety shut-off frame, which by pressing down stops the engine. The inlet hopper is oriented horizontally, which greatly facilitates insertion of long branches compared to the vertical or sloping hopper. Surface treatment of the whole machine is made with powder paint.

 

The Overload protection

If you put too large branch in the chipping-device, V-belts slip shortly and the engine stops. This is the way how to protect the branch logger against overload. When this situation happens, it´s usually impossible to take the branch outside of the chipping-device, because knives are jammed in the branch. In this situation, make sure the engine can not start itself, put away the small round cover of V-belts and turn over with the sheave clockwise until the branch is out of the chipping device. Then, please put the cover back on the place.

 

The chipping device

The working principle of branch loggers URBAN lies in two counter rotating shafts with knives. The rotating knives draw in the wood material into the feed hopper unassisted. The passage gap between the shafts is 70 mm. Each shaft has 3 fixed knives, made from high quality tool steel. It is possible to resharpen the knives repeatedly. After sharpening there is a pad to be put under the knives in order to keep the same gap between the knives (c. 0,1 mm). One single sharpening of knives is capable of producing from 100 to 500 solid meters of small logs, depending the level of contaminants (mud, nails, stones etc.). Each blade can be sharpened up about 4 mm, then it must be replaced with a new one.

Product inquiry

If you have a question about this product, do not hesitate to ask.

Items marked * are required.

Product variants

Photo Variant
URBAN SMH70 with belt conveyor 2,6 m within 4 weeks
URBAN SMH70 with turntable and belt conveyor 2,1 m within 4 weeks
URBAN SMH70 with turntable and belt conveyor 2,6 m within 4 weeks
URBAN SMH70 with folding conveyor 3,4 m within 4 weeks
URBAN SMH70 with turntable and folding belt conveyor 3,4 m within 4 weeks
URBAN SMH70 with double bagging within 4 weeks

Optional accessories

Related Products

Catalogues code

Engine oil 1 l

Bags for logs